|
Harlequin - $1499
• Spec: 6 Watts. Class A. Single ended output.
• Valves: 2 x 12AX7 (preamp), 1x EL84 (output stage)
• Cabinet: Solid pine with dove-tailed corners and ply baffle board permanently dadoed into cabinet.
• Dimensions: 600mm x 450mm x 250mm. Covered in custom made ox-blood vinyl.
• Speaker: 12 inch Celestion Vintage 30.
• Hardware: All corners, screws, cup washers, handle fixings etc are nickel plated. Powder coated chassis. Leather handle.
• Transformers: Custom designed in house and hand wound.
• Controls:
• Hi Input - This is a high impedance input so as to avoid loading passive guitar pick-ups. Treat this as the normal input.
• Lo Input - This is a lower impedance of - 6db sensitivity. This is the input to use should you want less gain. N.B. When both inputs are in use, they are both low sensitivity.
• Voice - The voice switch alters the frequency range over which the tone control operates.
• Volume - Simultaneously controls the 1st and 2nd gain stages (tandem pot).
• Bass - Adjusts the low frequency response of the pre-amp.
• Treble - Adjusts the high frequency response of the pre-amp.
• Master - Adjusts the overall output level.
• Mains - Power on / off switch.
• Speaker Output - Found on the underside of the chassis. Designed to connect the amplifier to 4 or 8 ohm speaker load and is important to note that a resistive load or loudspeaker must always be connected before switching the amplifier on to play.
|
Carrera - $1999
• Spec: 1x12 Combo. Output between 5 and 8 watts depending on the output valve used, single ended class A.
• Output stage: 1 x 9 Pin Valve Base Suitable for EL84/6BQ5, switchable to, 1 x 8 Pin Octal Valve Base Suitable for 6V6, 6L6/5881, EL34, KT66, KT77, KT88/6550. The Carrera comes with 1xEL84 and 1x 5881As standard. Switch to standby and leave for 10 seconds before switching valve bases.
• Preamp: 3x 12AX7's as standard, interchangeable with ECC81/12AT7,ECC82/12AU7, ECC803 and ECC83/12AX7,in any combination.
• Cabinet: Solid pine with ply baffle board permanently dadoed into Cabinet. Dimensions: 600mm x 450mm x 250mm, weight 21kgs. Covered in Custom-made ox-blood vinyl.
• Speaker: 12" celestion vintage 30, 8 ohm.
• Hardware: All corners, screws, cup washers, handle fixings etc. nickel plated. 16 gauge fully welded, powder coated chassis. Leather handle. Black cloth grill piped in cream.
• Transformers: Custom designed in-house and hand wound.
• Construction: Totally hand wired throughout and hand assembled. No PCBs Of any sort.
• Controls: Hi and lo inputs, Effects send and return, gain, reverb, bass, middle, treble and master volume. 8/9 pin output valve switch, standby and mains on off switches.
• Features: Valve powered effects loop. Valve powered reverb (accutronics 3-spring tank) Extension speaker socket, for 8 or 16 ohm extension cab (can be used with in conjunction with the internal speaker). Slave output, switchable output valves.
|
|
Hurricane - $2499
• Spec: 20 Watts. Class A
• Valves: 4 x 12AX7 (preamp), 2x EL84 (output stage)
• Cabinet: Solid pine with dove-tailed corners and ply baffle board permanently dadoed into cabinet.
• Dimensions: 600mm x 450mm x 250mm. Covered in custom made ox-blood vinyl.
• Speaker: 12 inch Celestion Vintage 30.
• Hardware: All corners, screws, cup washers, handle fixings etc are nickel plated. Powder coated chassis. Leather handle.
• Transformers: Custom designed in house and hand wound.
• Construction: Totally handwired throughout and hand assembled - no PCBs of any sort.
• Features: Effects loop, switchable valve powered reverb (accutronics full length 3 spring tank), 4 and 8 ohm speaker outputs.
• Accessories supplied: Reverb footswitch - handmade, powder coated, 14 gauge with 8mm top quality cable and Neutrik jack.
• Controls:
• Return/Send - Effects loop send and return. This is a series effects loop send level is - 6dbv. Suitable for foot pedals and rack processors.
• Hi Input - This is a high impedance input so as to avoid loading passive guitar pick-ups. Treat this as the normal input.
• Lo Input - This is a lower impedance of - 6db sensitivity.
N.B. When both inputs are in use they are both low sensitivity.
• Gain - Simultaneously Controls the 1st and 2nd gain stages (tandem pot).
• Reverb - This controls the level of the reverb effect. With the reverb knob turned fully anti clockwise, this is the same as turning the reverb off with the supplied footswitch: i.e. You don’t need the footswitch to turn the reverb off.
• Bass - Adjusts low frequency response of pre-amp.
• Middle - Adjusts frequencies around 500hz in the mid-range, which are very guitar friendly, unlike most amps you can dial mid-range and it works.
• Treble - Adjusts high frequency response of pre-amp.
• Master - Adjusts overall output level.
• On / Off Switch - Mains power switch for the amplifier.
• Mains - Neon, power on indicator
|
Hellcat - $3499
• Spec: 35 watt all valve head. Cathode bias, 2 channel with shared EQ, footswitchable reverb and channels.
• Valves: 4 x EL84’s. 5 x 12AX7’s
• Cabinet: 19mm ply lock-jointed. We still use pine for anything with a speaker in it as it helps the sound no-end but the heads will use ply, as they are not acoustic.
• Hardware: All corners, screws, cup washers, handle fixings etc. are nickel-plated. Bespoke CNC punched, powder coated grills. 16 gauge (1.5mm) powder coated chassis with 16 gauge base / screening plate secured to chassis with 4 machine screws. Leather handle.
• Transformers: Custom designed in-house and hand wound.
• Construction: Point to point hand wired throughout and hand assembled. No PCBs of any sort. Nothing board mounted. Everything is bolted directly to the chassis.
• Controls: Chicken head knobs. Metal toggle mains switches. 2 x inputs Hi and Lo.
Front panel from left to right:- gain modern channel 1, gain vintage channel 2, Bass, Middle, Treble, Master channel 1, Master channel 2, Reverb, Standby and Mains.
Rear Panel from left to right:- Mains Inlet, Mains fuse, HT fuse, Speaker impedance selector 4ohm, 8ohm, 16ohm, Speaker sockets x 2, Footswitch socket, Effects loop send and return.
• Accessories: Footswitch - hand made 14 gauge, powder coated, 2 metal footswiches. Top quality stereo lead wired to Neutrik nickel-plated stereo jacks. Mains lead, 10ft moulded plugs each end (at least it will reach the floor if you are using 2 cabinets). Speaker lead, 2ft top quality 8mm cable with nickel-plated Neutrik jacks.
• Gain - Modern channel 1: Higher gain channel. Controls the gain / overdrive on channel 1.
• Gain - Vintage channel 2: Lower gain channel. Controls the gain / overdrive on channel 2.
• Bass: Adjusts the low frequency response of the pre-amp.
• Middle: Adjusts frequencies around 500hz in the mid-range, which are very guitar friendly, unlike most amps you can dial in mid-range and it works.
• Treble: Adjusts the high frequency response of the pre-amp.
• Master channel 1: Sets the output level of the modern channel 1.
• Master channel 2: Sets the output level of the vintage channel 2.
• Reverb: Sets the reverb level for both channels.
• Speaker output: The speaker outputs are connected in parallel. Impedances from 4-16 ohms can be accommodated and it is important to note that a resistive load or loud speaker must always be connected before switching the amp on to play.
• Effects Loop: This is a series effects loop.
|
|
MK50H - $3299
• Spec: 50 watt all valve head. One channel with footswitchable master volumes and gain/overdrive (effectively the same as most companies 2 channel amps).
• Valves: 2 x 5881, 4 x 12AX7WA
• Hardware: All corners, screws, cup washers, handle fixings etc are nickel plated. Grills are bespoke CNC punched and powder coated. 14 gauge (2mm) powder coated chassis with 14 gauge base / screening plate secured to chassis with 4 machine screws. Leather handle.
• Transformers: Custom designed in house and hand wound.
• Controls: Chicken Head knobs. Metal toggle main switches. 2 x inputs (hi and lo). Front panel from left to right:- Volume/Gain, Overdrive (footswichable extra gain with red LED indicator), Bass, Middle, Treble, Master 1, Master 2 (footswitchable for volume lift, power amp, tonal differences etc. with green LED indicator), Presence, Resonance, Standby, Mains. Rear Panel from left to right:- Mains Inlet, Mains Fuse, H.T. Fuse, Speaker Impedance Selector 4, 8 or 16 ohms, Series Effects Loop send and Return, Footswitch Socket.
|
THE MK50II - $3999
• Spec: 50 watt all valve head. Two channels with foot-switchable master volumes gain/overdrive and effects loops.
• Valves: 2x6L6CHP. 4xECC83s/12AX7WA.
• Cabinet: 19mm ply lock-jointed.
• Hardware: All corners, screws, cup washers, handle fixings etc. are nickel plated. Bespoke CNC punched, powder coated grills. 16 Gauge (1.5mm) powder coated chassis with 14 gauge base / screening plate secured to chassis with 4 machine screws. Leather handle.
• Transformers: Custom designed in-house.
• Construction: Hand wired and hand assembled throughout.
• Features: Front panel from left to right: Input socket, - Clean Channel: Volume, Bass, Middle and Treble. Channel select switch. Overdrive Channel: Gain, Overdrive (foot switchable extra gain with red LED indicator), Bass, Middle, Treble and master volume. Global controls: Master 1 and Master 2 (foot switchable for volume lift with green LED indicator), Presence, Resonance, Standby/Mains switch. Rear panel from left to right: Mains inlet, Mains fuse, HT fuse, Speaker impedance selector (4 ,8, and 16ohms), 2 x series effects loop send and return sockets and footswitch socket.
• Accessories Supplied: Footswitch: hand wired, 16 gauge, powder coated, with 5 metal footswitches for: Channel, Master 2, Overdrive, Effects Loop 1 and 2 and Effects Loop Auto Assign.
7 metre footswitch lead.
3 metre mains lead.
Speaker lead, 600mm, top quality 8mm cable with nickel-plated Neutrik jacks.
|
|
RK100 - $3699
• Spec: 100 watt single channel Valve head, Valves 4 x JJ Tesla EL34's output stage, 4 x JJ Tesla 12AX7 pre-amp, bias switch to set the output stage for EL34's 6L6's 5881's etc. Totally hand wired, all components bolted directly to the chassis.
• Front Panel Controls: Guitar Input, foot switch input, Gain, Bass Middle Treble, Master Volume, Presence, Standby and Mains switches, front panel made of brushed stainless steel.
• Rear Panel Features: Mains input, Mains and 2 x valve failure fuses, Impedance Switch, 4 / 8 / 16 Ohms, 2 x Speaker Sockets, Valve Powered Series Effect Loop, Send and Return sockets, Rear Panel made of brushed stainless steel.
• Foot Switch: Labelled "HOT" with red LED switches amp between Hot and Cool modes.
• Cabinets: Head Cabinet made from 19mm Plywood lock jointed, finished in Kotzen Black Tolex, black leather handle, all hardware screws etc nickel plated. Speaker cab made from Solid Pine, finished in Kotzen Black Tolex, recessed black metal bar handles, custom grill cloth, and recessed stainless steel speaker socket panel with Neutrik locking jack. Fitted with Celestion Vintage 30's as standard, wired to 16 ohms.
• Weights: RK100 25kgs, 55lbs, RK4x12 35kgs, 77lbs.
|
Roadhouse 30 Head/Combo $1399/$1499
• Spec: 30-watt, cathode biased, valve guitar amplifier head and 1 x 12 combo.
• Valves: 2 x EL34, 3 x ECC83 (12AX7)
• Cabinet: 19 mm, lock jointed ply covered in black ‘Lizard’ vinyl with black grille cloth and white piping.
• Speakers: Celestion ‘Vintage 30’ (combo only)
• Transformers: Custom designed and built by one of the UK’s leading manufacturers.
• Accessories: All metal footswitch, to enable remote switching of the amplifier’s ‘Boost’ function.
• Effects Loop: Series effects loop. Send level is a nominal –6 dBV. Send impedance is 33k ohms. Return impedance is 145k ohms.
Roadhouse 50 Head and Combo $1899/$2199
• Spec: 50-watt, fixed biased, valve guitar amplifier head and 2 x 12 combo.
• Valves: 2 x EL34, 3 x ECC83 (12AX7)
• Cabinet: 19 mm, lock jointed ply covered in black ‘Lizard’ vinyl with black grille cloth and white piping. Metal bar type side handles.
• Speakers: 2 x Celestion ‘Vintage 30’ (combo only)
• Transformers: Custom designed and built by one of the UK’s leading manufacturers.
• Accessories: All metal footswitch, to enable remote switching of the amplifier’s ‘Boost’ function.
• Effects Loop: Series effects loop. Send level is a nominal –6 dBV. Send impedance is 33k ohms. Return impedance is 145k ohms.
|
|
ARTISTS
Guthrie Govan
http://www.myspace.com/guthriegovaneroticcakes
Rob Balducci
http://www.robbalducci.com/
http://www.myspace.com/robbalducci
Greg Howe
http://www.greghowe.com/
http://www.myspace.com/greghoweguitarist
Phil Hilborne
http://www.philhilborne.com/
http://www.myspace.com/philhilborne
Dave Kilminster
http://www.davekilminster.com/
http://www.myspace.com/davekilminster
Justin Hawkins
http://teamhotleg.com/
http://www.myspace.com/hotleg
Thomas Leeb
http://www.thomasleeb.com/
http://www.myspace.com/thomasleeb
Dweezil Zappa
http://www.dweezilzappa.com/
http://www.myspace.com/dweezilzappa
|
DEALERS
Cornford USA (Distributor)
Official US Cornford Tone Lounge & Artist Centre
P.O. Box 32291
Minneapolis, MN 55432 USA
Tel: 612-928-5562
www.cornfordusa.com
The Music Zoo
255-03 Northern Blvd
Little Neck, NY 11363
718-631-9292
www.themusiczoo.com
GuitarX
Denver, CO
303-282-9800
www.guitarx.com
Motor City Guitars
1565 Crescent Lake Road
Waterford, MI 48327
248-673-1900
www.motorcityguitar.com
Eddie's Guitars
7362 Manchester Rd
St. Louis, MO 63143
314-781-7500
www.eddiesguitars.com
Ultrasound
251 West 30th Street
4th, 5th & 6th Floors
New York, NY 10001
212-714-1079
www.ultrasoundrehearsal.com
EJ's Guitars 'n More
#221
321 Walnut Street
Newtonville
MA 02460
617-913-4444
www.ejsguitarsnmore.com
Rock n Roll Vintage
4740 N Lincoln Ave
Chicago, IL 60625
773-878-8616
www.rocknrollvintage.com
Make'n Music
1455 West Hubbard St
Chicago, IL 60642
312.455.1970
www.makenmusic.com
Tema Guitars
4081 St., RT44
Rootstown, OH
44272
330.325.2279
www.temaguitar.net
Wild West Guitars
1546 7th St.
Riverside, CA 92507
951-369-7888
www.wildwestguitars.com
Musician Supply
7001 St Andrews Rd.
Columbia, SC 29212
803-732-6900
www.musiciansupply.com
|
|
